Individual
VANDGARD® SAFE EDGE
Vandgard Safe Edge is new... a non- injurious Access Deterrent Measure or ADM. (Patent Pending) Manufactured only by Anti Climb Guards Ltd.
SAFE EDGE is an advanced version of the standard Vandgard product enabling its use at low level and in public places. The individual rotating vanes have engineered uniform edges 1.7mm wide in a sandpaper texture.
The edge is suitably uncomfortable to touch but not sharp or dangerous. Designed for use at low level and compliant with HSE requirements for use on Bridges and Exposed Pipes. It is ideal for Preventing access along walls pipes and bridges or for protecting low culverts , gates, and all types of fence, rooftops, windows and alleyways.
Finish:
Standard aluminium bare metal finish.
Note: Vanes are also available Polyester Powder Coated with a decorative finish.
Polyester powder coating is in accordance with BS 6496:1984 for application to aluminium alloy extrusion.
…
Stocked in Standard finish aluminium. Individual shaft/spindle lengths are one of the building components for Vandgard Rotating Anti Climb Guard. These Shafts are 1metre long. This product is usually supplied as a replacement or to make up or infill small sections of Barrier.
Vandgard is ideal for protecting walls, gates, and all types of fence, rooftops, windows and alleyways. In fact all situations where serious vandalism or theft is likely and particularly where Public Liability legislation applies. Examples include commercial and industrial sites, schools, vehicle parking areas, domestic, sports and leisure areas. This Anti-climb guard will eliminate any stable platform or foothold that an opportunist might otherwise use to scale a wall.
Corrosion free
In Stock
Next Day Delivery
Description:
Individual shaft length 26dia x1000 usually used with a joining spigot (Part number SPIGBAC01)
Pack Includes:
Spindle:
Extruded round tube BS6082
Fixing:
Vanes are threaded alternately onto the spindle which is crimped at the end with a hammer to secure the vanes. Vandgard must be supported at 2 metre intervals.
Finish:
Standard aluminium natural self colour…
Stocked in Standard finish aluminium. Individual shaft/spindle lengths are one of the building components for Vandgard Rotating Anti Climb Guard. Shafts are 2metres long. This product is usually supplied as a replacement or to make up or infill small sections of Barrier.
Vandgard is ideal for protecting walls, gates, and all types of fence, rooftops, windows and alleyways. In fact all situations where serious vandalism or theft is likely and particularly where Public Liability legislation applies. Examples include commercial and industrial sites, schools, vehicle parking areas, domestic, sports and leisure areas. This Anti climb guard will eliminate any stable platform or foothold that an opportunist might otherwise use to scale a wall.
Corrosion free
In Stock
Next Day Delivery
Description:
Individual shaft length 26dia x2000 usually used with a joining spigot (Part number SPIGBAC01)
Pack Includes:
Spindle:
Extruded round tube BS6082
Fixing:
Vanes are threaded alternately onto the spindle which is crimped at the end with a hammer to secure the vanes. Vandgard must be supported at 2 metre intervals.
Finish:
Standard aluminium natural self colour…
Individual vanes are the building components for Vandgard Rotating Anti Climb Guard. 2 of these individual vanes interlock to form a rotating pair. This product is usually supplied to make up or infill small sections of Barrier.
Colour coated Vandgard is visually softer than the standard version but no less effective. It is ideal for protecting walls, gates, and all types of fence, rooftops, windows and alleyways. In fact all situations where serious vandalism or theft is likely and particularly where Public Liability legislation applies. Examples include commercial and industrial sites, schools, vehicle parking areas, domestic, sports and leisure areas. This Anti-climb guard will eliminate any stable platform or foothold that an opportunist might otherwise use to scale a wall.
Popular in schools and conservation areas
Simple to assemble
Corrosion free
Approved by planners
Strong and effective without intent to harm
Complies with Health and Safety and Legal Liability
Green and Black in Stock! Any other colour possible: POA
Next Day Delivery
Description:
A freely rotating anti-scaling security obstacle designed to effectively roll away aggression and crime without intent to harm.
Includes:
1 individual vane ( Forms half of an interlocking pair in the illustration )
Fixing:
Vanes are threaded alternately onto a 26mm spindle which is crimped at the end with a hammer to secure the vanes. Vandgard must be supported at 2 metre intervals.
Finish:
Standard aluminium bare metal finish.
Note: Vanes are also available Polyester Powder Coated with a decorative finish.
Polyester powder coating is in accordance with BS 6496:1984 for application to aluminium alloy extrusion.
…
Inter Bracket for Rota 7.55 264.25 Spike Above RSJ Post (J4/04117/1) Galvanized (Palisade Inter)…
Junction Box GDELT-1• End of zone termination
• Weatherproof box sealed to IP66
• Easy termination
• Integral tamper switch
The GDELT provides a quick and easy method of terminating each zone of
sensor and provides access for service and ongoing maintenance of the
installation.
Sensor connections are made via terminal blocks mounted on a PCB contained
within the box which permits easy access for disconnection, testing and fault
finding if necessary. The box is sealed to IP66 rating and includes an integral
tamper switch operating in conjunction with the sensor monitoring circuitry,
therefore no additional tamper loop needs to be provided.
The kit contains all components necessary to enable the installation engineer to
install the unit on a fence or wall.…
The GDGBS Gate Bypass Switches provide the facility to disable the sensor in the area of a gate to allow the gate to be operated without generating an alarm. They are available in two versions, either the GDGBS-A/C which is a locally key operated switch or the GDGBS-B/D which is remote relay operated switch powered by 12V dc signal. Refer to the sensor installation manual QA189 for further details. 1. Terminate the ends of the sensor as described in Section 2. 2. Loosen the glands on the box and pass the sensor and feeder cable ends into the box so sufficient length is available on the tails to be wired into the terminal blocks. Refer to Figures 6 and 7 to determine which terminals, i.e. the small rectangles on the PCBs when the cables end, require to be configured with either Alpha Sensor or GQFC-9 dead cable. Figure 7 shows the Gate Bypass Switch on a single leaf or sliding gate and Figure 8 shows it on a double leaf or sliding gate. In both figures the Sensor is the thick solid line and the feeder cable is the thick chain dotted line. Tighten the glands by hand so that the rubber sealing ring grips the outer jacket and not the tails. 3. Position the boxes just above the line of the sensor to allow rain water to run away from the glands and fix to the fence using the mounting kit GDGBS GATE BYPASS SWITCHES 10 Figure 7 provided. The mounting bar is located across the diagonals of the box and is fixed in place by dropping the screws provided into the large holes at the corner of the box and screwing these into the mounting bar placed on the other side of the fence. If fixing the box to a wall or other solid surface the mounting bar can be dispensed with and the box fitted directly to the surface with appropriate fixings. 4. Connect the sensor tails to the terminal blocks on the PCB. 5. Replace the box lids, taking care not to over tighten the lid screws and verify that the tamper switch in each box operates by listening for the click of the switch action as the lid is screwed down. In order to attain a weatherproof seal the lid must be replaced with the correct orientation, i.e. with the chamfered edges vertical. …
Intermediate Spinner assembly to suit NB300 - NB624 Pipe Strap As G19 Specification…
Simple and fast to use. Simply drill and tighten. This fixing is for Vandgard support brackets fixed to Brickwork and Concrete…
M8 x 45mm 304 Stainless Steel Round Head Square Neck
Carriage Bolts and 40-50mm dia flat penny washer with M8
shear nuts …
Commercial Grade Neoprene Rubber Sheet Linear Meter A Size/Thickness: 10mm Thick x 100mm Wide x 1000mm Long Good For Mineral Oils Good For Greases Good For Sea Water Good Weathering & Outdoors Rubber Sheet Flame Retardant Not Recommended For Fuel Immersion …
Spinner assembly to suit NB80 - NB300 Pipe Strap As G19 Specification…
The effective, low-cost deterrent against unwelcome intruders, sold in boxes of 50metres. Fits to tops of fences, gates, pipes, walls, sills etc Designed to deliver maximum discomfort, but minimum harm Our unique double-hinge design allows easy fixing to angled surfaces Easy to use - the 500mm x 45mm strips can be screwed, nailed or glued* Fit side by side to increase effective width on walls, ledges and sills Made from unobtrusive neutral grey/brown polypropylene, Prikka-Strip is weatherproof and durable, re-usable and recyclable …
Clamp-On Rotating Anti-Climb Guard for Downpipes, Poles and Masts. Assembled and complete ready to clamp on to posts poles and masts using only 4 x 8mm bolts. Masts and lampposts adjacent to walls and high fences present an easy and common target for thieves to climb and attack property. A ring of Vandgard offers effective protection. Perfect for CCTV cameras and Satellite aerials and particularly where Public Liability legislation applies. Examples include commercial and industrial sites, schools, vehicle parking areas, domestic, sports and leisure areas. This pole protector will block access to any sensitive or valuable equipment above.
Simple to fix
Corrosion free
“Fix and forget” maintenance free.
Strong and effective without intent to harm
Complies with Health and Safety and Legal Liability
In Stock!
Next Day Delivery
Description:
A freely rotating anti-scaling security obstacle for 75mm to 200mm diameter poles and masts situated close to walls designed to effectively roll away aggression and crime without intent to harm.
Pack Includes:
Vandgard anti climb guard, ready assembled with support brackets on a 25x5mm flat steel axle curved around 270 degrees. The axle is welded to a clamop support for fixing to the mast or pole . Installation is simple and completed in minutes.
Comprising:-
Aluminium vanes made of corrosion free aluminium BS6082 (Dural)
Theoretical weight: 0.173Kg each Overall diameter approx 400mm.
Spindle:
25x5 galvanised mild steel bar
Fixing:
Clamped or welded to the supporting pole, mast or structure..
Finish:
Standard self-colour metal finish.
This product is also available Polyester powder coated in accordance with BS 6496:1984 for application to aluminium alloy extrusion.
Shipping:
Next Day shipping by TNT is charged at cost
(i.e. Currently £12.00 each + £12 per consignment)…
Clamp-On Rotating Anti-Climb Guard for Downpipes, Poles and Masts. Assembled and complete ready to clamp on to posts poles and masts using only 4 x 8mm bolts.Masts and lampposts present an easy and common target for thieves to climb and attack property. A ring of Vandgard offers effective protection. Perfect for CCTV cameras and Satellite aerials and particularly where Public Liability legislation applies. Examples include commercial and industrial sites, schools, vehicle parking areas, domestic, sports and leisure areas. This pole protector will block access to any sensitive or valuable equipment above.
Simple to fix
Corrosion free
“Fix and forget” maintenance free.
Strong and effective without intent to harm
Complies with Health and Safety and Legal Liability
In Stock!
Next Day Delivery
Description:
A freely rotating anti-scaling security obstacle for 75mm to 200mm diameter poles and masts designed to effectively roll away aggression and crime without intent to harm.
Pack Includes:
Vandgard anti climb guard, ready assembled with support brackets on a 25x5mm flat steel axle curved around360 degrees. The axle is folded to form a strong flange at both ends. Each flange is drilled with 10mm holes to receive fixing bolts to complete the circle. (fixing bolts are not supplied)
Comprising:-
Aluminium vanes made of corrosion free aluminium BS6082 (Dural)
Theoretical weight: 0.173Kg each Overall diameter approx 400mm.
Spindle:
25x5 galvanised mild steel bar
Fixing:
Bolted, clamped or welded to the supporting pole, mast or structure..
Finish:
Standard self-colour metal finish.
This product is also available Polyester powder coated in accordance with BS 6496:1984 for application to aluminium alloy extrusion.
Shipping:
Next Day shipping by TNT is charged at cost
(i.e. Currently £12.00 each + £12 per consignment)…
750@ 350mm Long - INTER SINGLE ROW Includes Oilite bearing St/st housing, Laser cut, fold and weld. Clamp to suit 750mm pipe Nylok Nuts Bolts + allow for 10mm Neoprene lining 750MM DIA @ 350MM LONG END – RA-71075…